Aladdin-light-lift ALL1000-CM-240V Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Aladdin-light-lift ALL1000-CM-240V. Aladdin Light Lift ALL1000-CM-240V User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 13
  • Table des matières
  • DEPANNAGE
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
ALL1000-230V
INSTALLATION
INSTRUCTIONS
Aladdin Light Lift, Inc. (256) 429-9700
61 Shields Road (877) 287-4601
Huntsville, AL 35811 www.aladdinlightlift.com
Patent #5105349
WARNING: Disconnect power source before servicing to avoid electrical shock
CAUTION: To Reduce the Risk of Electric Shock or Injury, Use Indoors Only.
Light and motor circuits are rated at AC 230V
Pour usage seulement dans un endroit
Avec acces au dessus du plafonds
Model Number: ALL1000(455Kg rated working load,7/32” steel galvanized lay cable,1.67amp,50/60Hz)
__ Greeneld _(if checked)
Light lift is equipped with a 35’(10.6m) cable unless checked below:
______65’(19.8m)
______90’(27.4m)
______120’(36.6m)
Light lift is equipped with a 2200 watt (20 amps)
lighting capacity
________________________
Manufacture Date © 2012 All Rights Reserved
Vue de la page 0
1 2 3 4 5 6 ... 12 13

Résumé du contenu

Page 1 - INSTRUCTIONS

ALL1000-230V INSTALLATION INSTRUCTIONSAladdin Light Lift, Inc. (256) 429-970061 Shields Road (877) 287-4601Huntsville, AL 35811 www.ala

Page 2 - ALL1000 Parts Bag List

STEP 23Adjust screw collar rings so top of canopy is just below edge of bottom contact plate. Canopy should be at least 4.4cm deep. See Diagram I.Nev

Page 3

STEP 27Tighten xture coupler set screws using supplied 3/32” Allen wrench. Fixture coupler set screws have thread lock already applied at factory. S

Page 4

ALL1000 TROUBLESHOOTING GUIDETECH SUPPORT: (877) 287-4601 Monday through Friday 8:00am to 4:00pm US CSTI. Troubleshooting and installation must be pe

Page 5 - Sheetrock

ALL1000 TROUBLESHOOTING GUIDE cont. 1. Conrm ALL1000 is at the CEILING POSITION. If not, use the controller to operate the ALL1000 to the CEILING P

Page 6

Read the following guidelines prior to installing the ALL1000:I. e ALL1000 must be installed by a licensed, bonded and insured electrician. II. e A

Page 7

STEP 1Determine where ALL1000 will mount on ceiling joists. ALL1000 must be installed level, in an accessible location directly above chandelier.Neve

Page 8

STEP 5Attach the 1/2” conduit connector on ceiling box to bottom of conduit assembly. Once completely inserted, tighten set screw on conduit connecto

Page 9

STEP 7Position ALL1000 where ceiling box will be centered in ceiling hole. Weight and bottom contact plate assembly should hang down through ceiling

Page 10

STEP 9Shim and adjust ALL1000 so that winch cable hangs plumb through center of hole in top contact plate on ceiling box. See Diagram E. Look up at

Page 11

STEP 11Turn o supply power before wiring ALL1000. Turn o motor switch in square box. Wire motor switch with 230V wiring. e 230V motor feed must b

Page 12 - ALL1000 TROUBLESHOOTING GUIDE

STEP 13Remove dust cover by using 5/16” nutdriver or socket. Remove paper tape from winch drum while keeping tension on winch cable.Never operate the

Page 13 - Warranty Agreement

STEP 20Fully thread screw collar loop or threaded stem that was supplied with chandelier to 3/8 IPS(16mm) xture coupler. If chandelier was supplied

Modèles reliés ALL1000-240V

Commentaires sur ces manuels

Pas de commentaire